PRESS2010_EN

170/1208

3.AD.Ai3.B.3.DDGBSLXAERDGdR.K.K.BALdH）l .0LWPAERDGR3A101010101053xamGP＞WDP≧WR＝0 is available forstandard type only.4−R≦0.2EP＞W）3nm（R10W±0.01W±0.01W±0.01W±0.01AA0　P0＋0±P0±P0±P0±P0　B0＋ynoR2（／W＜R≦518～254～ 64～25 ＋0.005 0±0.005φ0.0060.01 The drawings below are for standard type.　 But the precision above is for lapping type.P・KmaxWmaxP・WminRR 0.01PA 0.01（lapping type D6050 46050 560 65060 8（40）506010（40）5013（40）506016（40）（50）6020（40）（50）6025（40）（50）6060 460 560 6 860601060136016602025602525 56060 6 81013162025●Spring reinforced type3Days00　＋500　＋L　0−0.2H＋0.005　0−0.01−0.03R≦0.5R≦0.2R≦0.2φ0.010.02A0.01/120.02　0−0.01P≧W0.15≦R＜W／24−RShape R：K＝ （P−2R）2＋（W−2R）2＋2RShape D：K＝ P2＋W21.6Quick A@500/P@800/P168 For the overall length L（40）, tip length B＝6.　 For the overall length L（50）, tip length B＝13.ー0.03）. For special shaped tip, P・K＞Dー0.05, no press-in lead（Dー0.01 For ejector hole parameters, please refer to ejector punch blanks Code No.GGーSJAS13 ー50 ーP10.00GGLーSJEL20 －60 －P15.000 －W10.000TypeSKH51・SKD11SKH40SKH51・SKD11SKH40Spring reinforced type（D8～）GGーSJGGーSJVGGーPJGGーPJVGGLーSJGGLーSJVGGLーPJGGLーPJVSpring reinforced type（D8～）GGーSJGGーSJVGGLーSJGGLーSJVCode No.Shape 8 P.38 Express discount is available for 3 pieces or more of the same specification.404040131950505050505013193040 P.192、ejector pin sets P.194.The spring rigidity of ejector pin is doubled from 0.49N/mm｛0.05kgf/mm｝to 0.98Nmm｛0.1kgf/mm｝.Because of low spring rigidity, ejector pin was not in good performance before.Tip toleranceDーPCoaxialityADーP,WSymmetryERDGroughnessGL707070707070707070707070707070707070707070707080808080808080808080808080808080808080808080808080803.974.975.977.979.97 1.5 2 2.5 3 4 5.5 7 911.5 1.5 2 2.5 3 4 5.5 7 911.5 2 2.5 3 4 5.5 7 911.53.974.975.977.979.974.975.977.979.97　（JISG4403.2000）.4−R≦0.2GDREHardnessMaterial60～63HRCSKD1161～64HRCSKH5164～67HRCSKH40 SKH40:P/M high-speed steel 0.001）1.002.80 1.00～ 2.802.003.80 2.00～ 3.802.004.80 2.00～ 4.803.005.8090100 3.00～ 5.803.0090100 3.00～ 7.807.806.0090100 6.00～10.8012.9710.809010010.00～13.8015.9713.806.006.009010013.00～17.8019.9717.806.009010018.00～22.8024.9722.802.002.80 1.00～ 2.802.003.80 2.00～ 3.802.004.80 2.00～ 4.805.803.0090100 3.00～ 5.803.0090100 3.00～ 7.807.806.0090100 6.00～10.8012.9710.806.009010010.00～13.8015.9713.806.009010013.00～17.8019.9717.806.009010018.00～22.8024.9722.803.803.50 2.00～ 3.803.504.80 2.00～ 4.805.005.8090100 3.00～ 5.806.0090100 3.00～ 7.807.806.0090100 6.00～10.8012.9710.809010010.00～13.80ーーー9010013.00～17.80ーーー9010018.00～22.80ーーー 7 8 9111316192328 7 8 9111316192328 8 9111316192328Type・Precision / Material （Shank diameter tolerance D ）StandardLappingStandardSKH51・SKD11LappingSKH51・SKD11Tip0.16Ejector Shank Cutting PunchesStandard・Lapping Type