1033.AD.Ai3..3.DDGBAERDGSLXdR.K.K.BALdH）l .0WPLR1010101053xamGP＞WDP≧WR＝0 is also available.EP＞WBR≦0.2）3nm（R10W±0.01W±0.01W±0.01W±0.01AA0 P0＋0＋0 50±P0±P0±P0±P0 B0＋ynoR2（／W＜R≦518～254～ 64～25P・KmaxWmaxP・WminRR 0.01PAD6050 46050 560 65060 8（40）506010（40）506013（40）5016（40）（50）6020（40）（50）6025（40）（50）6060 460 5 66060 86010601360162060602560 5 660 81013162025●Spring reinforced type3Days5Days00 ＋L 0−0.2H＋0.005 0−0.01−0.03TiCNF coatingR≦0.5R≦0.2φ0.010.02A0.01/120.02 0−0.011.6P≧W0.15≦R＜W／24−R4−R≦0.2Shape R：K＝ （P−2R）2＋（W−2R）2＋2RShape D：K＝ P2＋W2is the range of coating（surface 2700HV）.F coatingTiCN P.1108 P.1110GGHーSJGGHーSJVGGHーPJGGHーPJVGGHーSJGGHーSJV For the overall length L（40）, tip length B＝6. For the overall length L（50）, tip length B＝13.ー0.03）. For special shaped tip, P・K＞Dー0.05, no press-in lead（Dー0.01 For ejector hole parameters, please refer to ejector punch blanks Code No.GGHーSJEL20 －60 ーP15.00 －W10.00Spring reinforced type（D8～）GHFーSJGHFーSJVGHFーPJGHFーPJVSpring reinforced type（D8～）GHFーSJGHFーSJV2.801.00～ 2.803.802.00～ 3.804.802.00～ 4.805.803.00～ 5.80901003.00～ 7.807.8090100901006.00～10.8012.9710.809010010.00～13.8015.9713.809010013.00～17.8019.9717.809010018.00～22.8024.9722.802.801.00～ 2.803.802.00～ 3.804.802.00～ 4.805.803.00～ 5.80901003.00～ 7.807.8090100901006.00～10.8012.9710.809010010.00～13.8015.9713.809010013.00～17.8019.9717.809010018.00～22.8024.9722.803.802.00～ 3.804.802.00～ 4.805.803.00～ 5.803.00～ 7.807.806.00～10.8012.9710.80ーーー1.002.002.003.003.006.006.006.006.002.002.002.003.003.006.006.006.006.003.503.505.006.006.00ーーー 1.5 2 2.5 3 4 5.5 7 911.5 1.5 2 2.5 3 4 5.5 7 911.5 2 2.5 3 4 5.5 7 911.53.974.975.977.979.974.975.977.979.97170TypeSKH51・SKD11SKH40SKH51・SKD11SKH40SKH51・SKD11 P.38Code No.Shape 84040401319505050505050131925253040 P.192、ejector pin sets P.194.The spring rigidity of ejector pin is doubled from 0.49N/mm｛0.05kgf/mm｝to 0.98Nmm｛0.1kgf/mm｝.Because of low spring rigidity, ejector pin was not in good performance before.707070707070707070707070707070707070707070707080808080808080808080808080808080808080808080808080809010090100901009010010.00～13.80ー9010013.00～17.80ー9010018.00～22.80ー （JISG4403.2000）.4−R≦0.2GDREHardnessMaterial60～63HRCSKD1161～64HRCSKH5164～67HRCSKH40 SKH40:P/M high-speed steel 0.013.974.975.977.979.97 7 8 9111316192328 7 8 9111316192328 8 9111316192328Type・Precision / Material （Shank diameter tolerance D ）F coatingTiCNF coatingSKH51・SKD11TiCNEjector Shank Cutting PunchesCoating （F coating・TiCN） Type
元のページ ../index.html#172