PRESS2010_EN

208/1208

CP03CBPBBTTTCBCLLCLLCTCLJCTCTP・W dimensions alteration●Reduce the tip“P・W”dimensions.Range of designationPC≧V×0.3≧1.00　WC≧H×0.15≧0.50P・W●Alter the tip“B”dimension.Range of designation2≦BC≦Bmax　　Unit of designation●Reduce the flange width dimension.Range of designation0≦HC＜1.5●Reduce the flange thickness“T”dimension.Range of designation2≦TC＜5H 6 8101316〜2・2.5・3・3.5・4●Alter the projection length of the ejector pin. Dimension AlterationCode@/PPC（200）WC（200）PC≧V×0.3≧1.50　WC≧H×0.15≧0.75（Tapped type）PC≧V×0.3≧1.00　WC≧H×0.15≧1.00（Coating type）Unit of designation 0.01PC・WC dimension alterations may shorten the tip B dimension.Ejector type is not available.Table 1 Tip shape AP（C）Bmax1013202530350.900〜1.1991.200〜1.4991.500〜2.9993.000〜4.4994.500〜5.9996.000〜BC（400） 0.1For tip length B≦L−30※（for tip shape A 30※→25、for flange thickness 10mm 30※→36）.Ejector typeRange of designation2≦BC＜BUnit of designation●Reduce the overall length“L”dimension.Range of designation30※＋B（C）≦LC＜L（for tip shape A 30※→25、for flange thickness 10mm 30※→36）. 0.1LC（200）20≦LC＜L（Straight type（standard type））30≦LC＜L（Straight type（coating type）、straight tapped type）. 0.1→Combined with LKC・LKP・LKPZ can be Unit of designationFor the overall length LC＜30※＋B（C）, tip length B（C）＝L−30※（for tip shape A 30※→25、for flange thickness 10mm 30※→36）.Ejector typeRange of designationLC＜LUnit of designation 0.1→Combined with LKC・LKP・LKPZ can be B is shortened according to（Ｌ−LC）,but B≧2.The ejector hole S is shortened according to（L−LC）.Flange holdersRange of designation20＜LC＜25Unit of designation 1h is shortened according to（Ｌ−LC）.L20・25 are available.HC（200）1.0≦HC＜2.0（flange thickness 10mm）Unit of designation 0.1TC（200）3.5≦TC＜5（ejector type）5≦TC＜10（flange thickness 10mm）Unit of designation 0.1→Combined with TKC・TKCM can be L is shortened according to（T−TC）.When LC is applied, L is equal to LC.Shoulder held type.Range of designation2≦TC＜25Unit of designation 0.1→Combined with TKC・TKCM can be The overall length L dimension is unchanged.JLC（200）Due to the probability of extended projection beingbroken, pay attention during selection please.Combined with JSC （ejector pin material alteration （SUS）） is available.206B dimension alterationL dimension alterationFlange width alterationT dimension alterationEjector pin length alterationWCW1.5（2.0）HC1.5（2.0）1.5（2.0）HCHC 0.01. 0.01. 0.01. 0.01.JLCNot available22・2.52・2.5・3Standard1.5Add. For details, refer to the specific page please.Spec.Table 2 Tip shape E・R・D・GBmax 4 8132030350.50〜0.991.00〜1.191.20〜1.992.00〜2.993.00〜4.995.00〜 Table 1,2Guide for Block Punches Addition