PRESS2010_EN

423/1208

52nm52nmERDGSSR−BBDERDGERDGERDG3APmin2.53AdSKD11SKH40dSKD11SKH40dSKD11SKH40dSKD11SKH40nuoRdradnaSepahs lacepSiit−−−−−3WPVYXHLWRPXY.i.iPVVHHJKilWdHYPXVWRPXYLepahs lacepSitnuoRnoneter parcS−−H08 −16 −P5.00 −W4.00 −R0.3 −X3.0 −Y6.2　 Position tolerance for round type：X,Y±0.005　special shaped type：X,Y±0.01　 The distance between designated shaped hole（P・W）and the shank（H・V）should be 2.5mm or more.（Right drawing）Round：H10 −16 −P5.00 −W4.00 −R0.3 −X4.5 −Y6.2 V20　 Position tolerance for round type：X,Y±0.005　special shaped type：X,Y±0.01　 The distance between designated shaped hole（P・W）and the shank（H・V）、bolt hole should be 2.5mm or more.Round：seD kcoBX0,Y0BBLDFPPBLDFBBLDPPBLDSSR−BLDFSSR−PBLDFSSR−BLDSSR−PBLDSSBLDSSPBLDSSBLDSSPBLDP.4243AP.4263ABlock Die BlanksBBBDBP.438EFRFDFGFEFRFDFGFCodeSSBLDFSSPBLDFSSBLDSSPBLDCodeEFRFDFGFFFBLDFFPBLDFFBLDFFPBLDSSR−FBLDSSR−FPBLDSSR−FBLDERDSSR−FPBLDGBBBD−BBBD−P.4303AP.4323ASSR−BBDERDGNameSpacers for Block DieShapeSSBDSSBDERDGP.440P.4343P.4363Wmin2.5Straight typeStraight typeSingle-flange typeQuill straight typeQuill single-flange typeV6～25H6～25L16～35Single-flange typeV6～25H6～25L16～35PageDeliveryFree size typeBolt fixed typeV6～25H6～25L16～35V13～50H8～25L16～35SKD11Shaped hole position alteration for block diesShaped hole position alteration for bolt fixed block dies The designation methods of X・Y for block dies and bolt fixed block dies are different, pay attention during selection please.CodeCodeX0,Y0 Usually the shaped hole centre on the shank （H・V） can be designated freely, refer to the ordering example belowCode No.VPPBLDR10 Designate the shaped hole centre position according to X・Y dimensions.X max.＝H−（2.5＋P／2） and X min.＝2.5＋P／2But for H−5≦P, X＝H／2 onlyY max.＝V−（2.5＋P／2） and Y min.＝2.5＋P／2But for V−5≦P, Y＝V／2 onlySpecial shaped：X max.＝H−（2.5＋W／2） and X min.＝2.5＋W／2But for H−5≦W、X＝H／2 onlyY max.＝V−（2.5＋P／2） and Y min.＝2.5＋P／2But for V−5≦P, Y＝V／2 only Usually the shaped hole centre is X＝J、Y＝H／2, but it can also be designated freely. Refer to the ordering example below.Code No.BBBDR Designate the shaped hole centre position according to X・Y dimensions.X max.＝V−（2.5＋P／2）−（K＋d／2） and X min.＝2.5＋P／2But for V−（K＋d／2）−5≦P, X＝K onlyY max.＝H−（2.5＋P／2） and Y min.＝2.5＋P／2But for H−5≦P, Y＝H／2 onlyBut for V−（K＋d／2）−5≦P, X＝K onlyY max.＝H−（2.5＋W／2） and Y min.＝2.5＋W／2But for H−5≦W, Y＝H／2 onlySpecial shaped：X max.＝V−（2.5＋P／2）−（K＋d／2） and X min.＝2.5＋P／2CodeCodeCodeBBLDBFPPBLDBFCodeCodeCode421V3～5H3～5L10～25Bolt fixed typeV13～50H8～25L16～35PageDeliveryType / MaterialMaterialSKD11SKH40NameShapeBBLDPPBLDBBLDPPBLDSSR−BLDSSR−PBLDSSR−BLDERDSSR−PBLDGNameShapeBBLDBPPBLDBPageDeliveryBlock DiesP.4283P.439PageDeliveryRoundspecial shapedPageDeliveryMaterialPagePageDeliveryDeliveryGuide for Block Dies