0°2ーD/2 0（Round 400）（Special shaped 200）（Round 600）（Special shaped 400）0°ー0.012ーD/2 00°P±0.005－L＋0.05 0L＋0.01 0T＋0.02 0D/2 0ー0.012.00＋ T1000＋ H●Alter the standard position of flat cutting.Range of designation0＜KC＜360Unit of designation●Add a flat cutting.ー0.01●Add parallel flats cutting.●Add parallel flats cutting.●Add two flats cutting at 0°・270°positions on the head.●Add designated-angled two flats cutting on the head.Range of designation0＜WKF＜360Unit of designationP＋0.005 0 0P±0.0022ーD/2 0P・W dimension tolerance alterationsP＋0.01 0P・W±0.01 Combined using of P・W dimension tolerance alterations are not available. Combined using of L dimension tolerance alterations are not available.T 0－0.02ー0.01ー0.01 Combined using of T dimension tolerance alterations are not available.Key flat tolerance alteration on the shank・Addition SKC・Addition SKF・Straight type－0.005－0.005－0.005D－1 02SKC 0SKF 0 0 0V・H＋0.005 0V・H 0－0.005V・H±0.002V・H＋0.01V・H±0.005 H＋0.01●Cancel the Press in lead（V,H－0.01 －－－－－－－－42...－－ii eduG hcnuPsgnhsuB－0.03）00＋＋LKCKCKC0°ー0.01WKF180°ー0.01ー0.01V・H dimension tolerance alterationsCode@/PKC（200）Straight type D≦6 is not available.Combined with WKC・CKC・WKF・SKC・SKF are not available.WKC（Round 400）（Special shaped 200）Straight type D≦6 is not available.Combined with KC・CKC・WKF・SKC・SKF are not available.Headed type is available.For special shaped type, combined with KC is available.Combined with WKC・WKF・SKC・SKF are not available. 1Headed type is available.Combined with KC・WKC・CKC・SKC・SKF are not available.Code@/PPKC（400）RoundSpecial shapedP・W＋0.01RoundPKCZ（400）Special shapedP・W±0.005RoundPNCZ（0）Special shapedLKC（400）LKP（600）TKC（200）TKCM（200）SKKC（400）VKC（600）VKCM（600）VKCZ（600）VNCM（400）VNCZ（400）Code@/PNDC（0）Flat cuttingParallel flats cuttingRight-angled two flats cutting on the headCKCDesignated-angled two flats cutting on the headWKFL dimension tolerance alterationT dimension tolerance alterationD/2 090°180°270°90°270°SKC 0SKF 0D/2ー1 0V,H－0.01－0.03 ・Straight（special shaped）type. ・SKC ・SKF 1Combined with KC90°180°270°Combined with KC90°180°270°445Add.Add.（Standard tolerance）Add.Press-in lead（V,H－0.01 －0.03）cancellingV,H－0.01－0.03Spec.Combined with WKC・CKC are available.Combined with WKF・SKC・SKF are not available.Combined with KC is available.（angle of two flats cutting can be designated）.Combined with CKC・WKF・SKC・SKF are not available.Spec. P≧1.00 is available. P・W≧1.00 are available. P≧1.00 is available. P・W≧1.00 are available. P≧1.00 is available. Combined using of the following alterations are required.Spec. Flat Cutting Alteration Tolerance Alteration OthersRound typeShaped holeTolerance alterationSpecial shaped typeRemarks
元のページ ../index.html#447