0°0°0°0°0°ー0.012ーD/2 0（Carbide drawing button dies 1,200）（Long shaped hole drawing button dies 200）（V-bending typePunches for Ribbing 200）0°0°0°0°ー0.010°（Carbide drawing button dies 1,800）（Long shaped hole drawing button dies 400）（V-bending typePunches for Ribbing 200）●Add a flat cutting.Punches・button diesD（P）/2ー1（0.5） 0●Add a flat cutting & flat cutting position alteration.For punches for ribbing.Range of designation0≦KC＜360Unit of designation●Add a flat cutting & flat cutting position alteration.Engraving punchesRange of designation0≦KC＜360 Unit of designationー0.010°ー0.01●Add parallel flats cutting & flat cutting position alteration.Engraving punchesRange of designation0≦WKC＜360Unit of designationー0.010° combined with KC Flat cutting alteration5 iignmroF rof seDnottuB& sehcnuPー0.01ー0.01KCKCKCKCKCKCKCKC90WKF180°Code@/PKC（200）（Carbide drawing button dies 600）Tapped type：D／2−1（for D5 is D／2−0.5）Embossing punches：P≧1.00 is available.Combined with WKC・CKC・WKF・SKC・SKF are not available.Drawing button dies：long shaped hole （B） type・dowel slot type are not available. 1 1The angle tolerance between stop flat and engraving character：±1°.Combined with CKC is available.Combined with WKC・WKF・SKC・SKF・KSC are not available.WKC（400）●Add parallel flats cutting.（Carbide drawing button dies 1,200）（Long shaped hole drawing button dies 200）（V-bending typePunches for Ribbing 200）For punches for ribbing, combined with KC is available.Combined with CKC・WKF・SKC・SKF are not available.Punches for ribbing：combined with KC.KC 1The angle tolerance between flat cutting and engraving character：±1°.Combined with KC・CKC・WKF・SKC・SKF・KSC are not available.Punches for ribbing：combined with KC.Engraving punches：combined with KC.Combined with WKC・WKF・SKC・SKF・KSC are not available.Engraving punchesRange of designation0＜WKF＜360Unit of designation 1Combined with KC・CKC・WKC・SKC・SKF are not available.90°180°270°180°270°90°90°180°270°270°90°180°180°270°270°180°Flat cutting alterationParallel flats cuttingRight-angled two flats cutting on the headCKC（400）●Add right-angled two flats cutting on the head.Designated-angled two flats cutting on the headWKF（600）●Add designated-angled two flats cutting on the head.Punches for ribbingPunchesD（P）/2 0ー0.01Button diesPunches for ribbingHeaded typeKCTapped typeKCEngraving punchesPunches2ーD（P）/2 0Button dies2ーD/2 0ー0.01Engraving punchesPunchesD（P）/2 0ー0.01Button diesPunches2ーD（P）/2 0Button dies2ーD/2 0ー0.01D/2 090°90°180°180°270°270°D/2 090°180°270°90°180°270°D/2 090°270°180°WKF270°90°The stop flat dimension of RRAMP1Combined with WKC・CKC are available.Combined with WKF・SKC・SKF are not available. Punches for ribbing：90°90°Alter stop flat position of V-bending punches for ribbing For engraving punches463Add.Spec.
元のページ ../index.html#465