0゜0゜P＋0.003 0 P,W＋0.005 0P 0－0.003 P,W 0－0.005 P 0－0.005 P,W 0－0.01 P±0.002 P,W±0.005 epahs lacepSepahs lacepSpyt dnuoRnuoRepahs lacepSdPC≧Pmin2 Table 1 0.001 Tip S・L are available.WC≧P・Wmin×2 0.01→Combined with PKC（M）can be dPC3≧1.00 Table 2 0.001.P・W dimensions alterationPCWC（Round 1,200）（Special shaped 2,500）e2≦BC≦Bmax Table 1d2≦BC≦Bmax Table 2d25＋B（C）≦LC＜Ld30＋B（C）≦LC＜L 0 0 0 －0.02 Table 1PD≦HC＜H2≦TC＜5P・WP・W dimension tolerances alterationPKCDERDGERDGAADiiiAERDGAERDGDDℓisehcnuP edbraCnuoR－0.03）cancellingNDC（0）V30WWPR□AA－WPR□WWPD□AA－WPD□WWPG□AA－WPG□V30LL－WPR□AAL－WPR□LL－WPD□AAL－WPD□LL－WPG□AAL－WPG□BC15B dimension alterationBC（600）L dimension alterationLC（600）H dimension alterationHC（600）T dimension alterationTC（600）Quantity discount rate P.38（ Prices less than 1Yen are rounded off）Code No.WWPDS4 － Product unit price＋Addition unit price.Price discount is also available for addition.1〜4100%5〜995%Standard・Mirror grinding10〜1490%P（C）L（C）50 －P3.05 －W2.00 －W（C）R（R only）（BC•HC•TC…etc）15〜2021〜85%Enquiry 90゜180゜270゜90゜180゜270゜Code（@/P）Add.Flat cutting on the headKC（600）Parallel flats cutting on the headWKC（1,200）Taper processing on the tipGC（1,200）Right-angled two flats cutting on the headCKC（1,200）Tip chamferingKey flat cancelling for special shaped punchesNKC（0）Add.Code（@/P）L dimension tolerance alterationLKC（1,200）L＋0.05LKP（1,800）L＋0.01LKPZ（1.800）L±0.005T dimension tolerance alterationTKC（1,200）T＋0.02TKCM（1,200）T 0WWXPR□AA－WXPR□WWXPD□AA－WXPD□WWXPG□AA－WXPG□LL－WXPR□AAL－WXPR□LL－WXPD□AAL－WXPD□LL－WXPG□AAL－WXPG□Table 2Bmax 413193040450.500〜0.9991.000〜1.9992.000〜2.9993.000〜3.9994.000〜5.9996.000〜1.000〜1.9992.000〜2.4992.500〜3.9994.000〜 P.648Code（@/P）CTC（600） 3 4 5 6 8101316Lapping 3 4 5 6 8101316WWPA□AA－WPA□MWPA□A－MWPA□3,9203,9804,0404,5405,8207,2008,73011,390WWPE□AA－WPE□WWPAXAA－WPAXMWPAXA－MWPAX4,6504,7004,7605,2706,5407,9209,45012,090LL－WPA□AAL－WPA□LL－WPAXAAL－WPAXLL－WPE□AAL－WPE□Add.Code（@/P） 0.1 BC≦L－25 0.1 BC≦L－30 0.1→Combined with LKC・LKP（Z） can be For LC＜25＋B（C）, B＝LC－25. 0.1→Combined with LKC・LKP（Z） can be For LC＜30＋B（C）, B＝LC－30. 0.1 0.1→Combined with TKC（M）can be L is shortened according to（5－TC）. When LC is applied, L is equal to LC.Add.Code（@/P）（Round 1,600）（Special shaped 2,300）PKCM（Round 1,600）（Special shaped 2,300）PNCM（0）PNCZ （0）8,1807,1207,1807,3908,83010,19011,96013,9604,8904,9305,0005,5106,7908,1709,69012,3505,6105,6605,7306,2307,5108,89010,42013,0809,6108,5608,6308,83010,28011,63013,40015,4008,4207,2907,3407,5709,13010,47012,29014,2907,4506,4406,5106,6208,1209,41011,35013,1207,2106,2306,2906,3507,8309,06010,91012,6809,8608,7308,7909,02010,57011,91013,73015,7408,9007,8907,9508,0609,56010,84012,80014,5708,6607,6707,7407,7909,28010,50012,35014,120Spec. 0.01. 0.01. 0.01.Spec. P.36Designated-angled two flats cutting on the headWKF（1,200）Tip R chamferingWWXPA□AA－WXPA□MWXPA□A－MWXPA□6,0506,1406,2206,8709,03011,170WWXPE□AA－WXPE□LL－WXPA□AAL－WXPA□LL－WXPE□AAL－WXPE□12,67010,97011,06011,37013,70015,780 3 4 5 6 8107,0207,1107,1807,8209,98012,12014,11012,42012,50012,82015,13017,230 3 4 5 6 81013,05011,21011,29011,60014,13016,23011,56010,05010,14010,29012,58014,57011,1909,7409,8209,90012,14014,06014,49012,65012,73013,05015,58017,66013,00011,49011,58011,73014,02016,01012,63011,19011,26011,34013,59015,500 Round type is available. Round type is available. Round type is available.Addition Details Add.Head chamferingHCC（1,600）HRC（2,000）Press-in lead（D－0.01 Spec.Bmax 8131925655Super corpuscleSuper corpuscle
元のページ ../index.html#657