PRESS2010_EN

96/1208

10101010100＋0　553xamGP＞WDP≧WR＝0 is available forstandard type only.4−R≦0.2EP＞W）3nm（R10W±0.01W±0.01W±0.01W±0.010±P0±P0±P0±P0　B0＋ynoR2（／W＜R≦518～254～ 64～25 ＋0.005 03.AAD3TA.Ai3.B.D3.DGBAESLGR.K.K.BAL）l .0HXLWRDR±0.005φ0.0060.01P・KmaxP・WminRR 0.01PAD6050 46050 560 65060 8（40）506010（40）5013（40）506016（40）（50）6020（40）（50）6025（40）（50）6060 460 560 6 860601060136016602025256025 560 660 81013162025●Spring reinforced typeThe spring rigidity of ejector pin is doubled from 0.49N/mm｛0.05kgf/mm｝to 0.98Nmm｛0.1kgf/mm｝.Because of low spring rigidity, ejector pin was not in good performance before.PP2.00P3.500 －W2.000 EGQuick T@1,000/P@1,600/PQuick A@500/P@800/P3Days00　＋L00　＋PR≦0.5Code No.SSJAS4 －40 －LL－SJDL4 －50 －A　0−0.2H−0.01−0.03φ0.010.02A0.01/120.02D／2　0−0.01P≧W0.15≦R＜W／24−RShape R：K＝ （P−2R）2＋（W−2R）2＋2RShape D：K＝ P2＋W21.694 Lapping type: for E・R・D・G, Quick T is not available. Express discount is available for 3 pieces or more of the same specification（except for Quick T）.TypeSKH51・SKD11SKH40SKH51・SKD11SKH40SKH51・SKD11SKH40SKH51・SKD11SKH40SKH51・SKD11Spring reinforced type（D8～）SSJVPPJVLLーSJVLLーPJVSSJPPJLLーSJLLーPJAAーSJAAーSJVAAーPJAAーPJVRAALーSJAALーSJVAALーPJAALーPJVDSSJLLーSJSSJVLLーSJVAAーSJAAーSJVAALーSJAALーSJVCode No.Shape P.38ー0.03）.　 For the overall length L（50）, tip length B＝13.404040 8131913193040Tip toleranceDーPCoaxialityADーP,WSymmetryERDGroughnessGL The drawings below are for standard type.　 But the precision above is for lapping type. P.192、ejector pin sets P.194 1070707070707070707070707070707070707070707070708080808080808080808080808080808080808080808080808080909090909090100100100100100100505050505050909090909090100100100100100100100100100100100100 For the overall length L（40）, tip length B＝6.　 For round tip, P＞Dー0.03, no press-in lead（Dー0.01ー0.03）. For special shaped tip, P・K＞Dー0.05, no press-in lead（Dー0.01 For ejector hole parameters, please refer to ejector punch blanks 9090909090901.00～ 3.992.00～ 4.992.00～ 5.993.00～ 7.993.00～ 9.996.00～12.9910.00～15.9913.00～19.9918.00～24.991.00～ 3.992.00～ 4.992.00～ 5.993.00～ 7.993.00～ 9.996.00～12.9910.00～15.9913.00～19.9918.00～24.992.00～ 4.992.00～ 5.993.00～ 7.993.00～ 9.996.00～12.9910.00～15.9913.00～19.9918.00～24.99　（JISG4403.2000）.4−R≦0.2GDREMaterialSKD11SKH51SKH40 SKH40:P/M high-speed steelHardness60～63HRC61～64HRC64～67HRC 0.01（Lapping type 3.974.975.977.979.9712.9715.9719.9724.973.974.975.977.979.9712.9715.9719.9724.974.975.977.979.9712.97ーーー 0.001）1.002.002.003.003.006.006.006.006.002.002.002.003.003.006.006.006.006.003.503.505.006.006.00ーーー 7 8 9111316192328 7 8 9111316192328 8 9111316192328Type・Precision / Material （Shank diameter tolerance D ）StandardLappingStandardLappingStandardLappingStandardLappingTip0.16Ejector PunchesStandard・Lapping Type